Skip to main content

TYPES OF ENGINE


HELLO FRIENDS,

We have discus in this topics of types of engine are used in automobile or automotive.  In Types of engine like petrol, diesel, CNG engine etc. types of fuel are used in internal combustion engine.

 














1. Types of fuel used:
 a) Petrol engine of gasoline engine, b) Diesel engine, c) gas engine

2. Cycle of operation
a) Otto cycle,  b) diesel cycle,  c) duel cycle engine or semi-diesel cycle engine

3. No. of strokes:
a) Two stroke engine, b) four stroke engine, c) hot spot ignition

4. Types of ignition:
a) Spark ignition engine( SI engine), b) compression ignition engine(CI engine)

 5. No. of cylinders:
a)Single, b) Two, c) Three, d) four, e) six, f) eight, g) twelve, h) sixteen

6. Arrangement of cylinder:
a) vertical, b) horizontal, c) redial, d) v-engine, e) opposed

7. valve arrangement:
a) L- head engine, b) I-head engine, c) F-head engine, d) T-head engine

8. Types of cooling:
a) air cooled, b) water cooled, c) evaporation

9. Speed:
a) low speed, b) high speed, c) medium speed

10. Method of fuel injection:
a) carburetor engine, b) air injection engine, c) airless or solid injection engine

11. method of governing:
a) hit and miss governed engine, b) qualitatively governed engine,
c) quantitatively governed engine,

12. Application:
a) stationary engine, b) automotive engine, c) locomotive engine,
d) marine engine, e) aircraft engine

other types of engines : other types of internal combustion engines are also being are used in automotive power plant.

We will describe step by step are deails on our website.I hope completely understand what is types  automobile and work of automobile can you more details are understand so you are subscribed my website and any queries regarding of automobile writing on comments box and share link I will give very fast reply and thank you for read this article.

Thank you🤗




Popular posts from this blog

Parts of engine -4

HELLO FRIENDS, Previous article we have discuss parts of engine crankcase, cylinder liner and piston introduction. In this article we have discuss material  of  piston and piston  clearance. So…..lets start,😊 Material  for piston : The material used for piston is mainly aluminium alloy. Aluminium piston can be either cast or forged. Cast iron is also used for piston. Yearly  cast iron was almost universal  material for piston because it's excellent  wearing qualities, co-efficient of expansion and general  suitability in manufacture. Due to reduce of weight of metal is necessary, light metal is lost. Aluminium is inferior to cast iron in strength and wearing qualities, and it's greater  co-efficient of expansion greater clearance in the cylinder to avoid the risk  of seizures. The thermal heat conductivity of aluminium  is about three times that of cast iron and this combined  with greater thickness necessary for s...

The Two-stroke engine working (Two stroke compresion ignition)

Hello friends, This time we discussed in two stroke compression ignition.   We have discussed in two stroke engine there is The desire of one working stroke in very revolution of the crankshaft has the development of two stroke cycle engine.  In two stroke cycle engine, the suction and exhaust are processe in cylinder. Compression stroke and power stroke these are usually called upward and downward stroke. There are two .Stroke inlet port and exhaust port in two stroke cycle engines. The burnt exhaust gases are forced out through exhusex port in two stroke cycle engines.  The principle of two stroke compresion ignition engine cycle  engine are show in figure are described under details. In compression engine only air is compressed inside the cylinder and fuel as used on diesel is injected by an injector fitted in the head of the cylinder. there are no use of spark plug in this engine. this engine are used in fuel injector. this operation of the two strok...

parts of engine -3

HELLO FRIENDS, Previous article we have discuss parts of cylinder block, cylinder head and this article we have discuss crankcase and cylinder liner and piston introduction. So…..lets start,😊 3. Crankcase: Crankcase is attached to the bottom face of the cylinder block. Crankcase is base on the engine. It is supported the crankshaft and camshaft in suitable bearings and provided the arm for supporting the engine on the frame. The oil pan and the lower part of cylinder block together are called the crankcase. Sometimes you are thinking about oil pan, so I can explain this oil pan is bottom half of the crankcase is called oil pan show in figure. it is bolted or screwed to the lower flange of the main casting are usually made of pressed  steel and aluminum. In the crankcase cylinder block and upper half of the crankcase usually are cast as single integral unit. This casting is usually made of a ferrous alloy or semi-steel provide to stronger and ...